Vba Code For Goal Seek To Run Automatically

Hello all,

New to the forums.

I'm in the process of creating a new report and I'm stuck.

My report consists of a set target in a field, a score and percentage of target.

e.g Target is 400

score is 450.

Percentage is 1.125 of target. (=score/target)

Now what I would like to do is create a formula that does not go above 100% , but instead work in reverse if you go over the target.

E.g. Target 400 .. Score was 450 ... percentage of target is 87.5%

Thanks in advanced.

Corporate edict.

I have a worksheet that is locked and protected now, except for cells in a certain collumn. I have named the cells in that column "MS96A".

If a user enters a date in a cell or range of cells anywhere in the column, the changed cells also need to be locked and protected (Once they enter a date, it is not allowed EVER to be changed again. Corporate requirement! *Shrug*).

What I am looking for is this. If the user selects that cell again, they will get the usual pop-up message, "The cell or chart that you are trying to change is protected..."

I think I am close, but I am getting an "End If without block If" error on the If Clause.


Sub Worksheet_Change(ByVal Target As Excel.Range)
Dim MRange As Range
Set MRange = Range("MS96A")
' If Not Intersect(Target, MRange) Is Nothing Then For Each cell In MRange Sheets("Sheet1").Unprotect Password:="temp"
cell.Interior.ColorIndex = 3
cell.Font.Color = vbBlack
Selection.Locked = True
Selection.FormulaHidden = False
Next cell
ActiveSheet.Protect Password:="temp", _
DrawingObjects:=False, _
Contents:=True, _
Scenarios:=False
ActiveSheet.EnableSelection = xlUnlockedCells
End Sub

Ok, I'm going to try and explain this. I am going to have 5 data points in cells such as A2:A6

All I need is to know if there is an upward trend or downward trend of the numbers.... I can't have something that simply takes the first and last number and checks if it's higher or lower. I need to actually see if they are trending upwards. Also how would i go about making it so that if they are trending upwards it shows an up arrow, and down arrow for downwards...

And finally, if the trend continues at the same rate, how long it will take the number to reach a goal. Each data point will be 1 week apart, with an ultimate goal needed to be achieved at the end.
This will be a completely separate formula on the sheet....

Any help?

I am looking for the code to select the visible data after applying a data filter. Actually I know how to select the data after applying the data filter but the issue is I am not able to exclude the header row and give the target range as used (non-blank) rows only!!

I am using below code to Select the Visible rows in the target range:

Code:

Range("A:p").SpecialCells(xlCellTypeVisible).Select

Problems in this code a

1) after applying the filter, while selecting the data it is selecting all the rows in given range till last row on the workbook. I need this to select the the data only till the last used row in the given range.

2) It is not possible to provide the address of the first row after we apply the filter since the first row address may change depending on the values in the table.

E.g. 1st time when I am running the macro the first row in the visible filtered data is starting at Cell address A4 and next time when I will run the macro it may be A6

3) The Code is also selecting the 1st row which is a header row. How can we exclude it from selection.

Some one please revert with the solution.
Thanks in advance.

Hi all.

I have set up a workbook that is sent out to lots of different users. They each keep and use their own copy.

I have set it up so that everything looks OK and is visible on MY screen, but I'm conscious that some users may have different screen sizes, different toolbars set up, and so on, which might make some parts not immediately visible to them.

I have set up an auto-execute macro which automatically sets the zoom factor to best fit, for several of the worksheets, and this works fine.
Here's the code that does it.
Code:

Sheets("WELCOME").Select
    Range("A1:N18").Select
    ActiveWindow.Zoom = True

By repeating this code for each worksheet, I can make each one be zoomed just right.

However, the file contains 8 sheets that are all identically laid out, except the number of rows is different.
What I want to do is go to the worksheet that has the largest number of rows (it's always the same worksheet, so I know which one it is), set the zoom factor for THAT worksheet (which I can do, and it always has the same number of rows), and then take THAT zoom factor, whatever it is - and it will vary depending on the user - and apply that to the other worksheets that have a similar layout.

I could just go through each worksheet and zoom it automatically, but that would mean that some of the sheets looked very large, others very small, and I'd like them to have a consistent appearance.
I could also specify a range on each worksheet that was similar to the appropriate range on the longest worksheet, and zoom that automatically, but that's not ideal either, because some of the row heights vary from sheet to sheet, and again I'll end up with different font sizes.

Anyone know how to do this ?